Home

Publications

List of publications

1. Life Cycle Assessment in the automotive industry: comparison between aluminium and cast iron cylinder blocks - HTDC 2006, Vicenza (21-22 September 2006) Franco Bonollo, Ilaria Carturan (DTG, Università di Padova, sede di Vicenza, Italy), Giuseppe Cupitò (Centro Ricerche Fiat, Orbassano, Italy), Roberto Molina (TeksidAluminum, Carmagnola, Italy)

2. NADIA: New Automotive components Designed for and manufactured by Intelligent processing of light Alloys - HTDC 2006, Vicenza (21-22 September 2006) Stefano Odorizzi - EnginSoft SpA, Padova, Italy

3. Comparative Corrosion-Wear behavior for cast iron and aluminium - EUROCORR 2006, Maastricht (23 September 2006) A. Igartua (Tekniker), R Bayon (Tekniker), R. Zabala (Abamotor), P. Zabala (Abamotor), V. Pais (Abamotor), J. Damborenea (Cenim), J.-P. Celis (KUL)

4. Microstructure, defects and properties in aluminium alloys castings: a review -ALUMINIUM 2000, Italy (13-17 March 2007) G. Timelli, F. Bonollo (DTG, Università di Padova, sede di Vicenza, Italy)

5. Theoretical Foundation of Energy Balance Determination during Deformation of Polycrystalline Materials - 1st Congress of polish Mechanics, Warsaw (28-31 August 2007) W.Oliferuk (IPPT PAN -Institute of Fundamental Technological Research, Polish Academy of Science, Warsaw, Poland) - in Polish

6. Aluminium casting in Europe - Technology, innovation and market - ALUSIL 2007, Moscow (3-5 December 2007) Mario Conserva (Edimet S.p.A., Italy), Franco Bonollo ((DTG, Università di Padova, sede di Vicenza, Italy)

7. A comparative study of defects and mechanical properties in high-pressure die-casting and gravity die cast aluminium alloys - HTDC 2008, Montichiari (9-10 April 2008) 1S. Akhtar, 1L. Arnberg, 2G. Timelli, 2F. Bonollo and 3M. Di Sabatino 1Department of Materials Science and Engineering, NTNU, Trondheim (NORWAY) 2Department of Management and Engineering DTG, Univeristy of Padova, Vicenza, (ITALY) 3SINTEF Materials and Chemistry, Trondheim (NORWAY)

8. A Probabilistic Approach For Modelling Of Fracture In Magnesium Die-Castings - HTDC 2008, Montichiari (9-10 April 2008) C. Dørum1, 3, D. Dispinar2, O.S. Hopperstad3 and T. Berstad2,3 1SINTEF Materials and Chemistry, Oslo, Norway 2SINTEF Materials and Chemistry, Trondheim, Norway 3Structural Impact Laboratory (SIMLab), Centre for Research-based Innovation, Trondheim, Norway

9. Microstructure vs Properties correlation in Al-Si Cast Alloys - HTDC 2008, Montichiari (9-10 April 2008) F. Grosselle, G. Timelli, F. Bonollo, A. Tiziani (DTG, Università di Padova, sede di Vicenza, Italy) E. Della Corte (EnginSoft S.p.A., Padova, Italy)

10. A new reference die for mechanical properties evaluation in die-casting - HTDC 2008, Montichiari (9-10 April 2008) F. Grosselle, G. Timelli (DTG, Università di Padova, sede di Vicenza, Italy) F. Voltazza (TOOLCAST, Brugine, Padova, Italy) E. Della Corte (EnginSoft S.p.A., Padova, Italy)

11. In-situ analysis phase formations in semi-solid state in the hypereutectic Al-Si alloy -published on “Kovove Materialy - Metallic Materials, vol. 46, 2008, pp. 63-69, Institute of Materials and Machine Mechanics, Slovak Academy of Sciences, Bratislava, Slovak Republic) A.V. Mazur, M.M. Gasik (Material Processing and Powder metallurgy laboratory, Helsinki University of Technology, Finland)

12. A comparative study of porosity and pore morphology in a directionally solidified A356 alloy -to be published on the International Journal of Metalcasting (by AFS) 1S. Akhtar, 1L. Arnberg, 2M.Di Sabatino, 2M. Syvertsen, 2F.Syvertsen 1Department of Materials Science and Engineering, NTNU, Trondheim (NORWAY) 2SINTEF Materials and Chemistry, Trondheim (NORWAY)

13. Numerical Modelling Of Magnesium Die-Castings Using Stochastic Fracture Parameters - to be published C. Dørum1,2, O.S. Hopperstad2, T. Berstad1, 2 and D. Dispinar1 1SINTEF Materials and Chemistry, Trondheim, Norway 2Structural Impact Laboratory (SIMLab), Centre for Research-based Innovation, Department for Structural Engineering, Norwegian University of Science and Technology, Trondheim, Norway

14. Effect of Hydrogen Content, Melt Cleanliness and Solidification Conditions on Tensile Properties of an A 356 alloy - ICASP-2 2008 (Second International Conference on Advances in Solidification Processes), Seggau, Austria (17-20 June 2008) 1S.Akhtar, 2D.Dispinar, 1L.Arnberg, 2M.Di Sabatino 1Department of Materials Science and Engineering, NTNU, NO-7491 Trondheim (NORWAY) 2SINTEF Materials and Chemistry, NO-7465 Trondheim (NORWAY)

15. Measurements of permeability of A356 aluminium alloys - ICASP-2 2008 (Second International Conference on Advances in Solidification Processes), Seggau, Austria (17-20 June 2008) D. Dispinar, K. Ellingsen, M.Di Sabatino, A. Mo SINTEF Materials and Chemistry, Trondheim, Norway

16. Nano-Scale Solidification Phenomena - to be presented at XXII ICTAM 2008, Adelaide, Australia (25-29 August 2008) J. Czerwinska, E. Deriaz & T. A. Kowalewski Institute of Fundamental Technological Research, Polish Academy of Science, Warsaw, Poland

17. Creep and Low Cycle Fatigue Investigations of light Aluminium Alloys for Engine cylinder Heads, A. Rutecka, L. Dietrich and Z. L. Kowalewski (IPPT, Warsaw), W. Rehm (Daimler AG, Ulm) – 12th EAEC European Automotive Congress

18. Thermo-Acoustics phenomena in the metal nanoparticles system generated by ultrashort laser pulse, Y. Bilotsky, M. Gasik (Helsinki University of Technology), N.Grigorchuk, P. Tomchuk (Institute of Physics, Ukraine);15th International Conference on Photoacoustic and Photothermal Phenomena

19. Evaluation of the Heat Treatment Role for Light aluminium Alloys subjected to creep and Low Cycle Fatigue, A. Rutecka, L. Dietrich and Z. L. Kowalewski (IPPT, Warsaw) – International Conference on Processing & Manufacturing of Advanced Materials

20. Crashworthiness Simulation of Mg Die Casting Parts including Local Properties from Process Simulation, H. Gese (MATFEM), A. Bach, U. Weiss (FORD), N. Nowack (IMPERIA), P. Bernbeck (MAGMA); 8th International Conference on Magnesium Alloys and their applications

21. Integrated design and Process Simulation for crash resistant Mg die casting parts, E. Hepp (MAGMA), S. Tewes (RWTH), U. Weiss (FORD); 8th International Conference on Magnesium Alloys and their applications

22. Simulation of porosity in gravity die casting Al-Si foundry alloys, S. Akhtar, (Department of Materials Science and Engineering, Trondheim) in collaboration with MAGMA and SINTEF

23. On the quality of A354 ingots and its impact on cast product, S. Akhtar, (Department of Materials Science and Engineering, Trondheim) in collaboration with MAGMA and SINTEF